Crew safety
Mooring and berthing safety for small ferries and passenger boats: risk assessment, snap-back and crew training
Mooring is one of the riskiest routine tasks on a small ferry or passenger boat. It happens often, right at the edge, with ropes under tension. If a line snaps, it can whip back with deadly force. According to MCA guidance, the entire mooring deck can be dangerous, not just the marked areas. The best safety measures are to assess risks at each berth, train crew to avoid standing in the path of a loaded rope, follow a set berthing sequence that secures the vessel before anyone goes ashore, and keep passengers away until the boat is safely tied up.
This guide uses diagrams to explain snap-back, outlines what the official guidance requires, and provides a checklist for risk assessment and crew training.
Why berthing is where people get hurt
A small ferry may dock twenty or thirty times a day. Each time, a crew member stands at the rail with a rope while the boat moves against the pontoon and passengers prepare to get off. Doing this so often can lead to shortcuts.
The hazards fall into four groups:
- Line recoil (snap-back). A synthetic rope under tension stores energy, much like a stretched elastic band. If it breaks or slips off a bitt, it snaps back along its path.
- Caught in the bight. This happens when feet or hands are inside a loop of rope, or fingers are between the rope and a bollard, just as the line tightens.
- Falling between the vessel and the berth. This can occur if crew step ashore carrying a rope before the boat is secure, or if passengers get off while a gap opens.
- Crush injuries. These can happen between the vessel and the pontoon, pier or fender as the boat comes alongside.
What the guidance says
Three MCA documents cover this ground.
MGN 592 Amendment 2 (anchoring, mooring, towing or hauling equipment on all vessels, October 2024). It applies to all vessels, small ones included. Three points stand out:
- "The whole mooring deck may be considered a danger zone."
- "Regardless of identified snap-back zones, seafarers should always be aware of other areas of potential danger."
- When a line is led round a pedestal fairlead, "the 'snap back' zone will change and increase in area."
MGN 648 (COSWP: self-mooring operations). This is the one most small passenger operators need. Its preferred practice is to moor from on board, using pre-rigged lines or by lassoing bollards, and to secure the vessel before the gate is opened. If crew must step ashore, they should make fast at least two lines first. Crew should not climb bulwarks, everyone should keep out of snap-back zones, and passengers should be kept clear of mooring operations.
COSWP 2026, chapter 26 (anchoring, mooring and towing operations). This is the working-practice detail, and it has two sections written for small operators:
- Section 26.7, safe mooring of domestic passenger craft. The recognised safe arrangement uses four lines: a head rope, a stern rope, a fore spring and a back spring. Do a risk assessment for the full mooring arrangement, including a diagram. Reduced arrangements are for exceptional circumstances only, and need their own risk assessment. Avoid single-point mooring and steaming on a spring, and keep passengers clear of all mooring and unmooring.
- Section 26.8, safe self-mooring. It sets a hierarchy: first, moor from on board with pre-rigged lines or by lassoing bollards, and secure the vessel fully before opening the gate. Second, partially self-moor from on board with at least two lines before anyone goes ashore. Only when neither is possible should crew step ashore while the vessel is unsecured, and the risk assessment has to cover that.
The chapter also says to "avoid painting snap-back zones on mooring decks because they may give a false sense of security", to treat the whole mooring deck as a danger zone, and to produce a bird's-eye view of the mooring deck to identify danger areas.
Industry guidance agrees. The UK P&I Club warns that painted snap-back zones "may give a false sense of security" and that "the entire area should be considered a potential snap-back zone".
Snap-back explained
Most modern mooring lines are synthetic, and these ropes stretch under load. When tension builds, they store energy. If a rope breaks or slips off a cleat or bollard, that energy is released instantly, causing the ends to snap back along the line and past where it was secured. The UK P&I Club points out that synthetic lines stretch more and hold more energy than older types.
The danger zone is not just the rope itself. It also extends behind the cleat, along the rope, which is often where a crew member stands to pull or control it.
The red areas indicate where the two loaded ropes could snap back. The safest places to stand are to the side of each cleat. Passengers should stay well away from both ropes, behind a gate, until the boat is securely tied.
Why painted zones aren't enough
A painted snap-back zone is marked for a specific rope direction. If you change the direction, the danger zone changes too. When a rope goes around a fairlead, roller or bollard before reaching the cleat, a broken line can whip around that turn and sweep across the deck.
On the left, the danger follows the rope and extends past the cleat. On the right, if the rope goes around a fairlead, it can sweep across the whole angle between both sections. On small ferries, where ropes are often led through different fairleads at different berths, painted zones are not reliable. Instead, explain the danger zone for each berth.
A safe berthing sequence
Stepping ashore holding a line before the boat is held is one of the most common ways deckhands end up in the water or crushed between hull and pontoon. COSWP section 26.8 and MGN 648 set out a better order: moor from on board where you can, and secure the vessel before the gate opens.
The highlighted step is what keeps everyone safe from that point on. Until the vessel is securely tied and the skipper is at the controls, keep the gate closed and have passengers remain seated. If crew must go ashore, secure two lines first, and always step carefully rather than jump.
Risk assessing your mooring operation
A general mooring risk assessment that fits any boat is not very useful. Assess each berth you use, since every one is different. COSWP asks for a risk assessment of the full mooring arrangement, including a diagram, and for the assessment to be reviewed for each new mooring configuration. Start from the four-line arrangement (head rope, stern rope, fore spring, back spring) and record why if you use anything less.
For each berth, record:
- The berth itself. Pontoon, pier, quay wall or slipway; bollard and cleat positions, fender condition, tidal range, lighting at night.
- Conditions. Typical tide, current and wind across the berth; wash from passing traffic; and the limits beyond which you won't berth or will change method.
- The method. Which lines go first, from where on deck, whether crew step ashore or moor from on board, and who controls the engines.
- Danger zones. Where each line leads on deck, where it could recoil, and where crew must not stand while it is loaded. Mark this on a simple deck plan.
- Crew numbers. What happens if you are short a deckhand? If the method relies on two people at the rail, write down what changes with one.
- Equipment condition. Rope inspection and replacement criteria; check bollards, cleats and fairleads for wear and sharp edges. The MAIB's Dart 8 report found abrasion had reduced a mooring rope's breaking load by 87.7%.
Keeping passengers clear. Passengers should remain seated or behind a gate until the vessel is securely tied and the gangway or step is ready. Let them know during the safety briefing, and have a crew member at the exit. In the MAIB's Hurlingham investigation, the vessel was held by only one line, the engine was in gear, and no one was in the wheelhouse. A gap opened while passengers were getting off without supervision, and one passenger fell in and drowned.
Crew training for line handling
New deckhands often learn mooring by copying their trainers, including any shortcuts. Make sure the training is clear and thorough.
- Induction at each berth. Show new crew the correct method for that berth, point out the danger zones on the deck plan, and explain the stop signal before they handle any ropes there.
- Stay out of the path of the rope. Never stand in a loop, on the rope, or in line with a loaded rope and the bollard or fairlead it passes around.
- Surge, don't snub. Teach crew how to ease a rope around a cleat or bitt with control, and when to let it go instead of holding on.
- Communication. Set clear hand signals and words between the deck and the wheelhouse. In the Dart 8 case, a missed order to loosen a rope played a role in the incident.
- Footwear and deck. Use non-slip shoes and make sure the mooring area has a non-slip surface. The MAIB's Hotspur IV report describes a deckhand slipping overboard while throwing a rope ashore.
- Sign-off. Record that each crew member is competent on each vessel and berth before they work unsupervised, and refresh it each season.
Practise emergency situations as well, such as a rope breaking, an engine failing during the approach, or someone falling into the water between the boat and the pontoon.
Lessons from MAIB investigations
- Hurlingham (Class V passenger vessel, report 12/2009): a passenger fell between the vessel and Westminster Pier while disembarking, and drowned. Held by a single line with the engine in gear and the wheelhouse unattended. Recommendations covered the master staying in the wheelhouse, gangway and passenger access, and protection if mooring lines part.
- Hotspur IV (passenger ferry, 1999): a deckhand slipped overboard while throwing the forward line to the pontoon. Recommendations on non-slip footwear and deck surfaces at mooring positions, and an MCA review of bulwark height.
- Dart 8 (ro-ro, report 12/2004): a mooring rope parted and recoiled, breaking the bosun's leg. He was standing in a snap-back zone. Abrasion had cut the rope's breaking load by 87.7%, and a missed slacking order was a factor.
- Svitzer Mercurius (tug, report 15/2022): a towline pennant failed and recoiled, injuring five crew. The pennant broke at about 52% of its original breaking load. Temporary crew had not been inducted.
Two of these examples involve larger vessels. The physics of a snapping rope are the same on a 12-metre ferry, just with smaller forces and less room to move out of the way.
Quick checklist
- A risk assessment for each berth, with limits for wind, tide and crew numbers
- A deck plan showing line leads and danger zones, posted and briefed
- A fixed berthing sequence: secure from on board, two lines fast before anyone steps ashore
- Passengers held back until the vessel is made fast and the exit is manned
- Ropes, bollards, cleats and fairleads inspected on a schedule, with replacement criteria
- Every crew member signed off on each vessel and berth before handling lines alone
- Agreed signals between deck and wheelhouse
- Near misses (line slips, slips at the rail, gaps opening) reported and acted on
How Helmsman helps
- Generic mooring risk assessment. Risk assessments and method statements per vessel and per berth, with the deck plan attached and review dates.
- New crew handling lines before they are trained. Crew inductions and competency tracking, with a sign-off per vessel and berth and reminders for seasonal refreshers.
- Worn ropes and fittings. Vessel inspection checklists and maintenance tasks for mooring lines and deck fittings, with defects raised from a phone.
- Line slips and near misses that go unreported. Incident and near-miss reporting, mapped to MAIB and RIDDOR categories, with corrective actions tracked to close-out.
- Briefings that change from skipper to skipper. Document control for the berthing procedure, with read-and-acknowledge records for each crew member.
Helmsman brings together your berth risk assessments, crew sign-offs and rope inspections, making sure the safe way to moor is always the documented way.
FAQs
What is a snap-back zone?
The area a mooring line could whip through if it parts or slips under load. It runs along and around the line and extends beyond the bollard or fairlead it is led round.
Are painted snap-back zones enough?
No. COSWP 2026 says to avoid painting snap-back zones because they may give a false sense of security, and MGN 592 says the whole mooring deck may be a danger zone. The zone changes whenever a line is led differently, and a line can part at more than one point.
Should crew step ashore to moor a small passenger boat?
Only as a last resort. COSWP section 26.8 and MGN 648 prefer mooring from on board, with pre-rigged lines or by lassoing bollards. Next best is to make fast at least two lines from on board before anyone goes ashore. Nobody should climb over bulwarks.
When can passengers get off?
Only when the vessel is secured, the gangway or step is in place and a crew member is at the exit. Keep passengers clear of mooring operations until then.
What should a mooring risk assessment include?
Each berth's layout and fittings, the tide, wind and wash limits, the mooring method, danger zones on the deck plan, crew numbers and equipment condition.
How often should mooring lines be inspected?
As part of your planned maintenance, with a visual check before use. Set replacement criteria for abrasion, cuts and UV damage. The MAIB has recommended rope inspection under a planned maintenance system.
Sources
- MGN 592 (M+F) Amendment 2: anchoring, mooring, towing or hauling equipment on all vessels
- MGN 648 (M): COSWP self-mooring operations
- Code of Safe Working Practices for Merchant Seafarers, 2026 edition
- UK P&I Club: Best practice, mooring snap-back zones
- MAIB reports linked in the lessons table above
Helmsman runs this six-stage process for you — capture to close-out, with the records joined up so they survive an audit.
Join the waitlistAbout this guide. Written by John Wilmans, a working skipper who has been through a domestic safety management audit from the side of the operator being audited.Reviewed by John Wilmans on 13 October 2026.
This guide is general information, not legal advice, and it describes United Kingdom (MCA), domestic passenger vessels, Workboat Code Edition 3, COSWP. Requirements differ between flag states and administrations — always confirm with your own flag state or administration. The diagrams are illustrative: they show principles, not measured zones for any particular vessel. Spotted something wrong?Tell me and I'll correct it.